INDUCTION HARDENING

Induction hardening is a method for hardening the surfaces of components, usually in selected areas, by the short-time application of high-intensity heating followed by quenching. The heating and hardening effects are localised and the depth of hardening is controllable. Unlike thermochemical case-hardening treatments (carburising / carbonitriding) applied to low-carbon steels, induction hardening does not promote chemical enrichment of the surface with carbon, but rely on the presence of an adequate carbon content already in the material to achieve the hardness level required.

INDUCTION HARDENING

WHAT ARE THE TREATMENTS?

Induction hardening involves passing a high-frequency alternating current through a suitably-shaped coil to induce rapid heating of the component surface situated appropriately within its electro-magnetic field. Depth of hardening is controlled by the parameters of the induction heating equipment, time of application and the hardenability of the material. A variety of manipulation procedures can be employed to suit the geometry of the component including ‘single-shot hardening’ in which the entire area to be hardened is heated in one operation then quenched, and ‘progressive hardening’ which involves relative movement between the heating coil, quench head and the workpiece. Selective area hardening can thus be achieved by the combination of suitable coil design and manipulation.

WHAT ARE THE BENEFITS?

Induction hardening imparts a hard, wear- resistant surface to the component whilst improving its fatigue strength through the development of residual surface compressive stresses in suitably deep cases. Because only the surface is heated and quenched, heat treatment distortion can be minimised.
Faster localised cooling rates permit higher surface hardness values than might be achieved by through hardening.
Deeper hardening can be obtained than with thermo- chemical treatments. Depending upon process parameters, hardened depths can be in the range 0.5-10mm.
Localised hardening can be used to strengthen components at critical points while leaving other areas soft, without the need for the stopping-off procedures required in thermochemical case-hardening.
Induction hardening offers options for the treatment of exceptionally large components, where conventional furnace heating and cooling would be impractical and where only localised surface hardening is necessary.
Induction Hardening can be automated for reproducible results once the processing parameters have been set.

WHAT SORT OF MATERIALS CAN BE TREATED?

Induction hardening can be applied to a wide range of steels and cast irons. Normally, medium-carbon steels (0.35-0.5% carbon), with or without alloying additions, are used to ensure a satisfactory hardening response, final choice depending on required surface hardness and core properties. With higher carbon contents there is an increased risk of cracking and careful control is necessary for successful treatment.
The process is used in certain circumstances for hardening previously-carburised surfaces on low-carbon steels.

Consult your heat treater when selecting materials for induction hardening.

WHAT SORT OF MATERIALS CAN BE TREATED?

Applications such as gears and shafts, which have readily-accessible and geometrically-uniform surfaces, are easily treated. Components with irregular shapes and surfaces requiring treatment can be difficult to induction harden in view of the restrictions imposed by coil design or limited accessibility.
The treatments can be applied to materials in the hardened and tempered, normalised or annealed condition. Because of its metallurgical structure, material in the hardened and tempered condition promotes optimum response to these short-time processes.
The size and shape of a component that can be induction hardened depends on the type of equipment operated by the heat treater. For large components, check the availability of suitably-sized facilities at an early stage.

WHAT PROBLEMS COULD ARISE?

Decarburised surfaces will not respond properly to induction hardening and must be avoided (e.g. parts made from cold-drawn bright bar which has not been machined on the diameter).
There is a danger of overheating thin sections and edges (e.g. keyways, oil holes, section changes, etc). Where possible, account should be taken of this factor at the design stage (by use of chamfers on edges, for example).

HOW DO I SPECIFY?

All of the following information should be included if possible.If uncertain, ask your heat treater before producing a specification:

Instruction: induction harden.
Material: identify the material used as accurately as possible using a BS number and grade or maker’s code.
Condition: indicate the existing heat treated condition (e.g. hardened and tempered).
Specify the hardened depth required, indicating a realistic acceptable range. State clearly whether this is an effective depth (to a specified hardness level) or a total depth (to core hardness level).
Specify the surface hardness required, indicating an acceptable range.
Provide drawings indicating selective hardening patterns.
Quote any relevant customer specification/ standard.
Where destructive testing is not admissible, representative test pieces (or scrap components) should be supplied for setting up and hardened-depth measurement.

WHERE DO I GO?

In order to locate contract heat treaters offering induction or flame hardening services, consult the current edition of CHTA’s Buyer’s Guide. It is advisable to involve your heat treater at an early stage before commencing manufacture.

This datasheet is compiled in good faith solely to assist others to evaluate the heat treatment techniques described. Users do so entirely at their own risk. NHTC is not responsible for any consequences from any such use. Datasheets shall not be used for contractual purposes neither directly nor by implication.